 |
8650F
Spiderbond
3506.9190
| Quantity: | |
|---|---|
Co-polyamide Film Adhesive
8650F
Description
Spiderbond 8650F film adhesive is a film form hot melt adhesive produced based on co-polyamide. Film adhesives handle like a fabric facilitating both intermittent and continuous processes. The CO-PA film is available in a range of thickness from 40 to 100 micron.
8650F film adhesive is based upon high performance co-polyamide polymer. This product offer good resistance to repeated home launderings, bond to a wide variety of textiles, foams, paper, leather, polymer materials, etc.
Advantages
VOC free adhesive in easy handle film form.
Strong bonding strength, good anti-washing performance and great chemical resistance.
Material properties:
Property | Detail or Method | Specification |
Appearance | By eye | Translucent film |
Base | Co-polyamide | |
Thinkness | micron | 50-200, tolerance ±10% |
Width | mm | ≤2500 |
Melting range | DSC, °C, GB/T 19466.3 | 95-110 |
Density | g/cm³, GB/T13354-1992 | 1.03 |
Packaging:
8650F film adhesives are sold in roll form, pack in carton.
For further packaging details please contact our salesperson.
Shelf Life:
8650F should be shipped and stored at temperatures below 50°C. The shelf life of 5008F is one year since production date under these conditions.
Directions for Using:
8650F can be activated with any of the following techniques: electric fusing press, heated rolls, heated air, radiant heat, or steam press. Dry heat activation recommend above 130°C.
Reactivation time is dependent upon technique, temperature, pressure, substrates, and adhesive thickness, but would typically be in a pressure of 2.0-3.0 kg/cm² or higher to the adherend, and maintain the pressure for 10~20 seconds to complete the bonding.
The surface of the adherend should be as clean and dry as possible, free of solvents and grease. Lower adherent surface temperatures or ambient temperatures will cause early adhesive coagulation, reducing open time and even causing adhesive shedding. Preheat the adherend if necessary.
Health & Safety Precautions
The Safety Data Sheet should be consulted for proper handling, clean up and spill containment before use. Keep containers covered to minimize contamination.
Health & Safety Precautions
The Safety Data Sheet should be consulted for proper handling, clean up and spill containment before use. Keep containers covered to minimize contamination.
Our Service:
1. Samples send to you free of charge.
2. Delivery on time, quality according to customer request.
3. OEM, ODM is welcome.
4. Support small wholesale, retails, Any inquires will be replied within 24 hours.
Co-polyamide Film Adhesive
8650F
Description
Spiderbond 8650F film adhesive is a film form hot melt adhesive produced based on co-polyamide. Film adhesives handle like a fabric facilitating both intermittent and continuous processes. The CO-PA film is available in a range of thickness from 40 to 100 micron.
8650F film adhesive is based upon high performance co-polyamide polymer. This product offer good resistance to repeated home launderings, bond to a wide variety of textiles, foams, paper, leather, polymer materials, etc.
Advantages
VOC free adhesive in easy handle film form.
Strong bonding strength, good anti-washing performance and great chemical resistance.
Material properties:
Property | Detail or Method | Specification |
Appearance | By eye | Translucent film |
Base | Co-polyamide | |
Thinkness | micron | 50-200, tolerance ±10% |
Width | mm | ≤2500 |
Melting range | DSC, °C, GB/T 19466.3 | 95-110 |
Density | g/cm³, GB/T13354-1992 | 1.03 |
Packaging:
8650F film adhesives are sold in roll form, pack in carton.
For further packaging details please contact our salesperson.
Shelf Life:
8650F should be shipped and stored at temperatures below 50°C. The shelf life of 5008F is one year since production date under these conditions.
Directions for Using:
8650F can be activated with any of the following techniques: electric fusing press, heated rolls, heated air, radiant heat, or steam press. Dry heat activation recommend above 130°C.
Reactivation time is dependent upon technique, temperature, pressure, substrates, and adhesive thickness, but would typically be in a pressure of 2.0-3.0 kg/cm² or higher to the adherend, and maintain the pressure for 10~20 seconds to complete the bonding.
The surface of the adherend should be as clean and dry as possible, free of solvents and grease. Lower adherent surface temperatures or ambient temperatures will cause early adhesive coagulation, reducing open time and even causing adhesive shedding. Preheat the adherend if necessary.
Health & Safety Precautions
The Safety Data Sheet should be consulted for proper handling, clean up and spill containment before use. Keep containers covered to minimize contamination.
Health & Safety Precautions
The Safety Data Sheet should be consulted for proper handling, clean up and spill containment before use. Keep containers covered to minimize contamination.
Our Service:
1. Samples send to you free of charge.
2. Delivery on time, quality according to customer request.
3. OEM, ODM is welcome.
4. Support small wholesale, retails, Any inquires will be replied within 24 hours.
