 |
5008F
Spiderbond
3506.9190
| Quantity: | |
|---|---|
Co-polyester Film Adhesive
5008F
Description
Spiderbond 5008F web adhesive is a film form hot melt adhesive produced based on co-polyester. Film adhesives handle like a fabric facilitating both intermittent and continuous processes. The CO-PES film is available in a range of thickness from 50 to 100 micron.
5008F film adhesive is based upon high performance co-polyester polymer. This product offer good resistance to repeated home launderings, bond to a wide variety of textiles, foams, paper, leather, polymer materials, etc.
Advantages
VOC free adhesive in easy handle film form.
Strong bonding strength and good anti-washing performance.
Material properties:
Property | Detail or Method | Specification |
Appearance | By eye | Milky white translucent film |
Base | Co-polyester | |
Thinkness | micron | 40-100, tolerance ±10% |
Melting range | DSC, °C, GB/T 19466.3 | 95-115 |
Melt Flow Index | g/10min at 160°C, GB/T 3682-2000 | 25-35 |
Density | g/cm³, GB/T13354-1992 | 1.1-1.2 |
Packaging:
5008F web adhesives are sold in roll form, pack in carton.
For further packaging details please contact our salesperson.
Shelf Life:
5008F should be shipped and stored at temperatures below 50°C. The shelf life of 5008F is one year since production date under these conditions.
Directions for Using:
5008F can be activated with any of the following techniques: electric fusing press, heated rolls, heated air, radiant heat, or steam press. Dry heat activation recommend above 150°C.
Reactivation time is dependent upon technique, temperature, pressure, substrates, and adhesive thickness, but would typically be in a pressure of 0.2MPa or higher to the adherend, andmaintain the pressure for 10~20 seconds to complete the bonding.
The surface of the adherend should be as clean and dry as possible, free of solvents and grease. Lower adherent surface temperatures or ambient temperatures will cause early adhesive coagulation, reducing open time and even causing adhesive shedding. Preheat the adherend if necessary.
Health & Safety Precautions
The Safety Data Sheet should be consulted for proper handling, clean up and spill containment before use. Keep containers covered to minimize contamination.
Our Service:
1. Samples send to you free of charge.
2. Delivery on time, quality according to customer request.
3. OEM, ODM is welcome.
4. Support small wholesale, retails, Any inquires will be replied within 24 hours.
Co-polyester Film Adhesive
5008F
Description
Spiderbond 5008F web adhesive is a film form hot melt adhesive produced based on co-polyester. Film adhesives handle like a fabric facilitating both intermittent and continuous processes. The CO-PES film is available in a range of thickness from 50 to 100 micron.
5008F film adhesive is based upon high performance co-polyester polymer. This product offer good resistance to repeated home launderings, bond to a wide variety of textiles, foams, paper, leather, polymer materials, etc.
Advantages
VOC free adhesive in easy handle film form.
Strong bonding strength and good anti-washing performance.
Material properties:
Property | Detail or Method | Specification |
Appearance | By eye | Milky white translucent film |
Base | Co-polyester | |
Thinkness | micron | 40-100, tolerance ±10% |
Melting range | DSC, °C, GB/T 19466.3 | 95-115 |
Melt Flow Index | g/10min at 160°C, GB/T 3682-2000 | 25-35 |
Density | g/cm³, GB/T13354-1992 | 1.1-1.2 |
Packaging:
5008F web adhesives are sold in roll form, pack in carton.
For further packaging details please contact our salesperson.
Shelf Life:
5008F should be shipped and stored at temperatures below 50°C. The shelf life of 5008F is one year since production date under these conditions.
Directions for Using:
5008F can be activated with any of the following techniques: electric fusing press, heated rolls, heated air, radiant heat, or steam press. Dry heat activation recommend above 150°C.
Reactivation time is dependent upon technique, temperature, pressure, substrates, and adhesive thickness, but would typically be in a pressure of 0.2MPa or higher to the adherend, andmaintain the pressure for 10~20 seconds to complete the bonding.
The surface of the adherend should be as clean and dry as possible, free of solvents and grease. Lower adherent surface temperatures or ambient temperatures will cause early adhesive coagulation, reducing open time and even causing adhesive shedding. Preheat the adherend if necessary.
Health & Safety Precautions
The Safety Data Sheet should be consulted for proper handling, clean up and spill containment before use. Keep containers covered to minimize contamination.
Our Service:
1. Samples send to you free of charge.
2. Delivery on time, quality according to customer request.
3. OEM, ODM is welcome.
4. Support small wholesale, retails, Any inquires will be replied within 24 hours.
